Loading...

概述

An easy-to-deploy 2-axis encoding phased array (PA) solution, the semiautomated HydroFORM™ scanner enables fast and reliable wall-thickness mapping and midwall damage detection by acquiring high-resolution data of large surfaces in minimal time. While the standard HydroFORM package comes equipped with the proven phased array linear probe and local immersion system, you can now choose for a dual array probe configuration. Both options allow for a resolution of up to 1 mm × 1mm.

To optimize the productivity of raster scanning, the HydroFORM system is equipped with several efficiency-boosting features:

Integrated X and Y axis encoders
Smart indexing button
Index position and coupling indicators
Scan speed check
Efficient bubble management (with I8 linear probe)
Easy-to-index magnetic wheels (with REX2 DLA probe)
Braking system

Easily adapting to curvatures 4 in. OD (101 mm) and greater, this PA solution facilitates a wide range of applications including:

Monitoring wall-thickness reductions due to corrosion, abrasion, and erosion
Detecting midwall damage, such as hydrogen-induced blistering or manufacturing-induced lamination, and differentiating these anomalies from loss of wall thickness

XY mapping principle on pipes with the HydroFORM and ChainSCANNER.

High-Performance Corrosion Mapping for Rough and Uneven Surfaces Using the I8 Local Immersion System

Achieve immersion-tank-quality phased array inspection without concerns about water coupling. The HydroFORM scanner's unique low-flow water-column design with foam gaskets conforms to the surface, eliminating the need for a wedge.

Other innovative features of the HydroFORM water-coupling system:

Coupling check LED indicates when the water supply is too low
Gasket protector to prolong the use-life

Effortless High-Resolution Corrosion Mapping with the REX2 DLA Probe

Increase the versatility and efficiency of corrosion mapping with the HydroFORM scanner by opting for the REX2 Dual Linear Array™ probe.

See critical defects closer to the surface thanks to its high near-surface resolution enabled by angled transmitter-receiver arrays.
Optimized for phased coherence imaging (PCI) and total focusing method (TFM) imaging, improving the detection of corrosion mechanisms such as H2S.
Hard-wedged suspension system removes the need for an external water pump, easing difficult-access inspections, such as rope access or at heights.
Wheel stabilization promotes smoother scanning (compared with a carbide system).
64 mm long active area and larger coverage (dual 64-element or dual 32-element) accelerates data acquisition, permitting high-throughput scanning with automated scanners, such as the motorized MapROVER scanner and remote-controlled SteerROVER scanner.

ScanDeck™ Module

Integrated Controls and Status Indicators

The ScanDeck module is like your scanning dashboard, situated directly in your eyeline while you operate the HydroFORM scanner.

Using a combined HydroFORM and OmniScan™ X4 solution, you fully benefit from all the functionalities of the ScanDeck module.

Control button:

Start the data acquisition on the OmniScan X4 unit
Switch between guided and freehand scanning modes
Toggle between index and scan axis scanning

Indicator LEDs:

Index position guidance
Insufficient coupling warning
Alert when maximum scan speed exceeded
Active encoder (X or Y)

ScanDeck Module

Complete PA Solution

HydroFORM Scanner and Omniscan^™ X4 Multitechnology Flaw Detector

By combining a water column system with gate synchronization on the interface echo available in the OmniScan X4 software, the HydroFORM scanner provides class-leading signal quality, reliable remaining wall measurements, and an enormous improvement in flaw characterization and imaging over conventional UT.

When combined with the REX2 DLA probe, the HydroFORM scanner further improves the near-surface resolution for applications where a constant water flow is impractical or logistically impossible. The REX2 DLA probe is also compatible with the latest advanced ultrasonic technologies, such as TFM and PCI.

配置

Manual Encoded

An easy-to-deploy 2-axis encoding PA solution, the HydroFORM scanner has integrated X and Y axis encoders.

Semiautomatic

The HydroFORM mounted on a MapSCANNER.

Automatic

Conduct automated 2-axis corrosion mapping at high acquisition rates using the motorized MapROVER™ scanner and HydroFORM scanner.

Learn More

Achieve PA corrosion mapping in difficult-to-reach locations using the remote-controlled SteerROVER™ motorized scanner and HydroFORM scanner.

Learn More

HydroFORM技术规格

	HydroFORM	DLA Corrosion	DLA Corrosion
Phased array probe	7.5L64-I8	REX2	REX2-1DEG
Maximum one-line scan coverage (width)	60 mm	60 mm	60 mm
Delay line medium	Water	Rexolite	Rexolite
Delay line height	14 mm or 38 mm	7.5 mm	7.5 mm
Roof angle	N/A	5°	1°
Maximun inspektion thickness (in steel)	50 mm (14 mm delay line) 150 mm (38 mm delay line)	30 mm (recommended)	95 mm (recommended)
Typical near-surface resolution (1/8 in. FBH)	1.5 mm	1 mm	1 mm
Depth resolution	0.1 mm	0.1 mm	0.1 mm
OD inspection range	4 in. and greater	4 in. and greater	4 in. and greater
ID inspection range	10 in. and greater (16 in. with index encoder)	10 in. and greater (16 in. with index encoder)	10 in. and greater (16 in. with index encoder)
Dimensions	16 cm × 12 cm × 8.5 cm with index encoder	16 cm × 12 cm × 8.5 cm with index encoder	16 cm × 12 cm × 8.5 cm with index encoder
Scanner compatibility	ChainSCANNER, SteerROVER, MapSCANNER, and MapROVER	ChainSCANNER, SteerROVER, MapSCANNER, and MapROVER	ChainSCANNER, SteerROVER, MapSCANNER, and MapROVER