Olympus Around the World

Evident Around the World

Watch these video tutorials made by Evident’s global team of experts to help you get the most out our products.

主页/ 奥林巴斯遍布全球/ Evident Around the World

HomeEvident Around the WorldOmniScan™ X3 Phased Array Flaw Detector

OmniScan™ X3 Phased Array Flaw Detector

Everything you need to know about the OmniScan X3 flaw detector.

New

What’s New in MXU 5.16, the OmniScan™ X3 Onboard Software

How to Calibrate Phased Array (PA) Wedge Delay with the OmniScan™ X3 Flaw Detector

What’s New in MXU 5.14 and 5.15, the OmniScan™ X3 Onboard Software

Stephan Couture Alexandre Gregoire

DMA和DLA探头解决方案

如何在OmniScan X3仪器上校准PA声速

使用OmniScan X3进行手动PA焊缝检测

探头和UT技术如何有助于探测到碳化铬包覆层中的裂纹

EVIDENT遍布全球（第25集）：MXU 5.13软件的新功能

如何在OmniScan X3探伤仪上创建多组TFM设置

EVIDENT遍布全球（第21集）：如何设置和使用OmniScan X3的远程协作服务（RCS）

MXU 5.12软件的新功能

Tommy Bourgelas Trevor Tartaglia

Quebec City, Canada

WeldSight™ Software Workflow for Phase Coherence Imaging (PCI) Data Analysis

Vertical Notch Detection Demonstration Using TFM and the OmniScan™ X3 Flaw Detector

What’s New in MXU 5.11

Stephan Couture Trevor Tartaglia

Quebec City, Canada

使用OmniScan X3 64仪器的TFM和PCI模式对高温氢致（HTHA）缺陷进行检测的比较

采用相控阵/超声技术检测螺钉和螺栓

Carlos Enrique Suárez Navas

OmniScan™ X3系列搭载软件MXU 5.10新特性

Stephan Couture Trevor Tartaglia

Преобразование Гильберта и огибающая TFM

Emilie Peloquin

How it Works: Full Matrix Capture (FMC) and the Total Focusing Method (TFM)

Curtis Dickinson

如何使用OmniScan™ X3超声波探伤仪校准PA灵敏度

Как создать 3-точечную ВРЧ с помощью OmniScan X3

What's New in MXU 5.9.0

Stephan Couture Louis-Philippe Gendron

Как создать настройку из 4 групп TFM с помощью OmniScan X3 и сканера WeldROVER

План сканирования и настройка в дефектоскопе OmniScan™ X3 для контроля

Настройка контроля в режиме мультигрупп в дефектоскопе OmniScan® X3

ASME Section V: Проверка производительности TFM

Prasanth Geddam

What’s New with the OmniScan™ X3 Flaw Detector’s Software, MXU version 5.7, and OmniPC 5.7 Software

Stephan Couture Tommy Bourgelas

OmniPC™ Corrosion Analysis using the FlexoForm™ Scanner

用于无损检测腐蚀分析和报告的OmniPC™ 5

在OmniScan™探伤仪上设置用于腐蚀检查的RollPerform™

MagnaFORM™ Eddy Current Lift-Off Compensation

Michaël Barbeyrol

Export C-Scan data on the OmniPC™ software

Setup and Inspection with the FlexoFORM™ Scanner and the OmniScan™ X3 Flaw Detector

2 Axis C-scan Creation with OmniScan™ X3 Software Clicker

Wilbert Rooyakkers

What's New in MXU 5.6.0

Louis-Philippe Gendron

如何在OmniScan®X3探伤仪上创建用于焊缝检查的多组TFM设置

Using the OmniScan® X3 Flaw Detector for HTHA and Other Micro-Fissuring Applications

Stephan Couture

OmniPC™ - TFM weld analysis

Manual TCG on the OmniScan® X3

OmniPC™ Weld Analysis

Sensitivity Calibration on the OmniScan X3

Yuichiro Yamamoto

How to Create a Basic Phased Array Setup for Weld Inspection using the OmniScan X3

Efficient Long Seam Weld Inspection

Overview of Conventional UT on the OmniScan X3

How to create a Scan Plan with DLA and DMA probes on the OmniScan X3

How to perform sensitivity calibration for DMA and DLA probes on the OmniScan® X3

Dead Element Check on DMA probe with OmniScan® X3

How to create custom probes and wedges on the OmniScan® X3

OLYMPUS AROUND THE WORLD_Vid07_Калибровка задержки в призме — OmniScan® X3

Stephan Couture

Overview of A.I.M tool on the OmniScan® X3

Prasanth Geddam

OmniPC™ 5.2 Software

Overview of the User Interface on the OmniScan® X3

Curtis Dickinson

Introduction of the Scan Plan on the OmniScan® X3

Stephan Couture

File Managment on the OmniScan® X3

How to Update the Software on the OmniScan® X3

What's New in MXU 5.2

Stephan Couture

Ультразвуковой толщиномер 27MG — Краткий обзор

Sorry, this page is not available in your country

Sorry, this page is not available in your country

Let us know what you're looking for by filling out the form below.

Sorry, this page is not available in your country